Humminbird HDR 650 Bedienungsanleitung

531874-1_BHDR 650 Installationand Operations ManualHDR 650 Installationand Operations Manual

4. Installing the HDR 650After the mounting hole has been cut (see section 2), continue the installation asfollows:1. Insert the HDR 650 through the f

5. Installing the BuzzerSecure the buzzer to a nearby wire bundleusing the cable ties (included).6. Connecting to the Power SupplyUse the following in

CAUTION: Some boats have 24 or 36 Volt electrical systems. Make sure that yourHDR 650 is connected to a 12 VDC power supply. Use a voltage conditioner

Transducer Installation OverviewFind the correct section for your transducer installation type. If you have atransom mount transducer, you can mount i

Transom Transducer Installation1. Locating the Transducer Mounting PositionNOTE: If transom mounting is not possible because of a stepped hull or cavi

• On boats with stepped hulls, it may be possible to mount the transduceron the step. Do not mount the transducer on the transom behind a stepto avoid

2. Preparing the Mounting LocationIn this procedure, you will determine the mounting location and drill twomounting holes, using the transducer mounti

3. Continue to hold the bracket on the transom ofthe boat, and use a pencil or marker to markwhere to drill the two mounting holes. Mark thedrill hole

1b. If you do not know your transom angle,measure it using a plumb line (weightednylon string or monofilament line) exactly 12inches long. Hold the to

3. Put the pivot bolt through the assembly tohold it in position and loosely install the nut,but do NOT tighten the nut at this time (seethe illustrat

Thank You!Thank you for choosing Humminbird®, America's #1 name in fishfinders.Humminbird® has built its reputation by designing and manufacturin

4. Align the mounting bracket transducerassembly with the drilled holes in thetransom. With a 5/16" socket driver, mountthe assembly to the trans

6. Adjust the initial angle of the transducer from back to front by rotating thetransducer until the side seam on the transducer is almost parallel wi

9. Mark the correct position on the transom by tracing the silhouette of thetransducer mounting bracket with a pencil or marker.10. Tighten the pivot

CAUTION! Do not cut or shorten the transducer cable, and try not to damage thecable insulation. Route the cable as far as possible from any VHF radio

4. Route and secure the cable by attaching the cable clamp to the transom;drill one 9/64" diameter x 5/8" deep hole, then fill hole with mar

NOTE: The transducer must be submerged in water for reliable transducerdetection.4. If the unit is working properly, gradually increase the boat speed

If you do change the transducer position, re-trace the position of the mountingbracket before proceeding.NOTE: It is often necessary to make several i

7. Drill the third mounting hole, using a 5/32” drill bit. Use a marine-gradesilicone sealant to fill all three drilled mounting holes, especially if

7. Locking Down the Transducer (Optional)NOTE: You have the option to lock down the Two Piece Kick Up bracket if you donot want the transducer to kick

Inside the Hull Transducer InstallationIn-hull mounting generally produces good results in single-thicknessfiberglass-hulled boats. Humminbird® cannot

Table of ContentsiHow Sonar Works 1Installation Overview 2Installing the HDR 650 ...

2. Trial InstallationYou will not be able to adjust the mounting after an inside the hull transducer isinstalled. It is best, therefore, to perform a

4. Fill the hull with enough water to submerge the transducer body. Use asand-filled bag or other heavy object to hold the transducer in position. The

4. Permanently Mounting the TransducerNOTE: Once permanently mounted, you will not be able to make furtheradjustments to the transducer.1. Make sure t

7. If you unplugged the transducer cable at the beginning of this procedure,plug it back into the depth sounder.NOTE: The connector is keyed to preven

Operating the HDR 650Your HDR 650 Digital Depth Sounder sends a sound wave signal and determinesdistance by measuring the time between the transmissio

Power On/OffThe power is controlled by the power source connected to the HDR 650. Whenthe power source is turned on, the HDR 650 is powered on. When t

UnitsThe Units control function selects the units of measure for depth readoutand alarm functions. You can set the units of measurement to feet, meter

Shallow AlarmThe Shallow Alarm will sound when the measured depth is less than the setting.1. Press the MENU key until the Shallow Alarm icon is displ

Deep AlarmThe Deep Alarm will sound when the measured depth is greater than the setting.1. Press the MENU key until the Deep Alarm icon is displayed a

Set Offset (waterline or keel)The Set Offset function adjusts the digital depth readout to display depthreadings from the waterline or the keel (lowes

Table of ContentsiiOperating the HDR 650 30The HDR 650 Control Head...

MaintenanceTo keep both your HDR 650 and your transducer working properly, perform thefollowing maintenance tasks as needed.HDR 650 MaintenanceIf your

TroubleshootingBefore contacting the Humminbird® Customer Resource Center, please read thefollowing section. Taking the time to review these troublesh

No Bottom Reading on the DisplayIf there is no bottom reading visible on the display, there are a number of possiblecauses for this condition, includi

1-Year Limited WarrantyWe warrant the original retail purchaser that products made by Humminbird®have been manufactured free from defects in materials

Humminbird® Service PolicyEven though you'll probably never need to take advantage of our incredibleservice policy, it's good to know that w

Returning Your Unit for ServiceBefore sending your unit in for repair, please contact the factory, either by phoneor by email, to obtain a Repair Auth

SpecificationsDepth Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .600 ft (180 m)Power Cable Length . . . . . . . .

ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Humminbird®to be a responsible corporate citizen, operating in compliance with known andapp

Contact Humminbird®Contact the Humminbird® Customer Resource Centerin any of the following ways:By Telephone:(Monday - Friday 8:00 a.m. to 4:30 p.m. C

How Sonar WorksSonar technology is based on sound waves. The HDR 650 Digital Depth Sounderuses sonar to determine depth directly below the transducer.

Installation OverviewBefore you start installation, we encourage you to read these instructionscarefully in order to get the full benefit from your HD

Installing the HDR 650You will install your HDR 650 depth sounder first, then your transducer. Whenyou are done with both of these installation tasks,

1. Locating the HDR 650 Mounting PositionYou must select an appropriate mounting location for the HDR 650. Considerdifferent positions on the console

3. Customizing and Assembling the HDR 650Your HDR 650 includes a variety of face plates and trim rings so that you cancustomize the appearance.1. Sele